The Sedan Exhaust Thread
#316
Has anyone tried the Magnaflow cat-back exhaust? It has an X pipe and 2.25" mandrel bent pipes.
$1063 on Amazon
https://www.amazon.com/MagnaFlow-168.../dp/B001O02LAM
$1063 on Amazon
https://www.amazon.com/MagnaFlow-168.../dp/B001O02LAM
#317
Premier Member
Clips of the 2010 & 2013 with Invidia Q300
The clips sound similar to me but the cars don't sound the same on the road, either inside the cabin or out...
That's why I'm making the Monstrosity... I want more volume and sexual expression from her... Mine's the '13 in case you're new...
Thoughts?
BTW, the custom exhaust guy said he'd do the job if I find stainless elbows, and accept the fact non-tig welding would rust unless painted. I'm going to do it.
Frank
That's why I'm making the Monstrosity... I want more volume and sexual expression from her... Mine's the '13 in case you're new...
Thoughts?
BTW, the custom exhaust guy said he'd do the job if I find stainless elbows, and accept the fact non-tig welding would rust unless painted. I'm going to do it.
Frank
Last edited by FrankRoshi; 02-01-2017 at 08:40 AM. Reason: Typos
#319
Has anyone tried the Magnaflow cat-back exhaust? It has an X pipe and 2.25" mandrel bent pipes.
$1063 on Amazon
https://www.amazon.com/MagnaFlow-168.../dp/B001O02LAM
$1063 on Amazon
https://www.amazon.com/MagnaFlow-168.../dp/B001O02LAM
#320
Administrator
iTrader: (9)
Sleeves and clamps, instead of bolts, gaskets and flanges. And a computer generated image, instead of actual photos, even on their own website.
And if you're having a difficult time finding reviews... Danger, Will Robinson.
And if you're having a difficult time finding reviews... Danger, Will Robinson.
The following 2 users liked this post by Rochester:
2GoRNot2G (02-09-2017),
guy from norcal (02-04-2017)
#321
Registered Member
iTrader: (4)
Stillen uses all Magnaflow components for their exhaust. This looks identical to the stillen setup with the exception to utilizing an X pipe. Given it's using quality components, X pipe, and a reasonable price. I think it's the better exhaust in its price range against the competitors in that bracket.
#322
My old Buschur Racing 3" exhaust on my GVR4 had sleeves and clamps. Less weight and easier to make sure it is aligned. I was more worried about the sound level but I would think it would have the best flow for a cat-back system.
#323
Premier Member
Who needs a welder? All you need is testosterone and power tools...
Flex hose?
Sleeves and clamps?
What say you? Got impatient. Started cutting...
I could be growling tomorrow... but for Super Bowl parties...
Sleeves and clamps?
What say you? Got impatient. Started cutting...
I could be growling tomorrow... but for Super Bowl parties...
#325
Premier Member
Ok... I will... headed for Harbor Freight now...
The duct tape is temporary. If it'll duct tape, it'll weld!
This will require a little more cutting and fitting...
I accept your challenge!
This will require a little more cutting and fitting...
I accept your challenge!
#327
Premier Member
Custom MeganVidiaManzo Hybrid Update
Harbor Freight- $99!
Organization is the key to success...
The flange on the left rail of the jig is one of two that came from the Invidia x-pipe. I'm going to put them between the forward part of the x-pipe and the rear of the cut off Megan y-pipe. I want to make the system installable in two pieces.
Getting close. Two more cuts and I'm ready to weld!
Organization is the key to success...
The flange on the left rail of the jig is one of two that came from the Invidia x-pipe. I'm going to put them between the forward part of the x-pipe and the rear of the cut off Megan y-pipe. I want to make the system installable in two pieces.
Getting close. Two more cuts and I'm ready to weld!
#328
Registered Member
iTrader: (4)
Harbor Freight- $99!
Organization is the key to success...
The flange on the left rail of the jig is one of two that came from the Invidia x-pipe. I'm going to put them between the forward part of the x-pipe and the rear of the cut off Megan y-pipe. I want to make the system installable in two pieces.
Getting close. Two more cuts and I'm ready to weld!
Organization is the key to success...
The flange on the left rail of the jig is one of two that came from the Invidia x-pipe. I'm going to put them between the forward part of the x-pipe and the rear of the cut off Megan y-pipe. I want to make the system installable in two pieces.
Getting close. Two more cuts and I'm ready to weld!
#329
Administrator
iTrader: (9)
...FI doesn't use a flex-pipe.