Pros and Cons, Axel back or muffler delete?
#31
Registered User
iTrader: (1)
You guys seriously just overlooked me telling you oem piping size is 1.9"? I measured it with a digital caliper...
Edit: and just because I am a nice guy despite being completely ignored...
Measurements taken from a 2013 Sedan oem exhaust
Piping size immediately before connecting to mufflers is 1.9" OD
Piping size between resonators and mufflers is 1.6" OD
Piping size before resonators 2" OD
Piping size at y pipe connection where both y's meet 2.5" OD
Piping size right after catalytic converter but measured on y pipe side is 1.9" OD
Edit: and just because I am a nice guy despite being completely ignored...
Measurements taken from a 2013 Sedan oem exhaust
Piping size immediately before connecting to mufflers is 1.9" OD
Piping size between resonators and mufflers is 1.6" OD
Piping size before resonators 2" OD
Piping size at y pipe connection where both y's meet 2.5" OD
Piping size right after catalytic converter but measured on y pipe side is 1.9" OD
Last edited by 4doorfury; 08-13-2016 at 12:37 PM.
The following users liked this post:
ETrev (08-13-2016)
#32
Registered Member
iTrader: (2)
I'm not positive, I wanna say you're right on 2.25", that's what my tip inlet size is. I just told the shop to keep the stock size piping.
I don't have any from up close. I could get some if you needed. I was unsure about what tip size to go, as I didn't want them to be too large and wanted them to be subtle. I went rolled angle cut 3.5" tips. They look good, but they look pretty small. I may eventually up-size to 4" tips, but i'm content for now.
They're filthy, but you get the idea of how they sit.
I don't have any from up close. I could get some if you needed. I was unsure about what tip size to go, as I didn't want them to be too large and wanted them to be subtle. I went rolled angle cut 3.5" tips. They look good, but they look pretty small. I may eventually up-size to 4" tips, but i'm content for now.
They're filthy, but you get the idea of how they sit.
#33
Premier Member
You guys seriously just overlooked me telling you oem piping size is 1.9"? I measured it with a digital caliper...
Edit: and just because I am a nice guy despite being completely ignored...
Measurements taken from a 2013 Sedan oem exhaust
Piping size immediately before connecting to mufflers is 1.9" OD
Piping size between resonators and mufflers is 1.6" OD
Piping size before resonators 2" OD
Piping size at y pipe connection where both y's meet 2.5" OD
Piping size right after catalytic converter but measured on y pipe side is 1.9" OD
Edit: and just because I am a nice guy despite being completely ignored...
Measurements taken from a 2013 Sedan oem exhaust
Piping size immediately before connecting to mufflers is 1.9" OD
Piping size between resonators and mufflers is 1.6" OD
Piping size before resonators 2" OD
Piping size at y pipe connection where both y's meet 2.5" OD
Piping size right after catalytic converter but measured on y pipe side is 1.9" OD
Thanks, I'm lucky to live in a pretty awesome place!
#35
Ok, I'm on a budget and don't have the money for the exhaust system I want right now. I've been looking around and seen that there's axel back exhaust systems for the car. After doing more research I seen that cats are doing muffler deletes which is a much cheaper option and I could the money saved away towards the exhaust system I want. My question is what are the pros and cons about doing the muffler delete if any, would it be better to get an axel back than do the muffler delete?
Thread
Thread Starter
Forum
Replies
Last Post