What did you do to your Sedan today?
#9301
Registered Member
So if you scroll up a little bit you'll see I ordered about $2000 of parts from Z1. Well 2-3 days later Z1 started a promotion to win the new Z, modified pretty well, and $20,000 for every dollar you spend. They even have multipliers for buying specific products, like their own are worth 4x the amount of a standard spent dollar. I was a little disappointed, so I emailed them asking if I could have some entries for my order. They said no, because it was before the contest date, however since none of my stuff had shipped yet they let me cancel my order and place it again, today. The bulk of the money I spent was Z1 parts (about $1500), so that would be over 6000 entries alone! Pretty happy how this worked out, and that Z1 allowed me to do that. Some of it was just luck that they hadn't shipped yet.
The following users liked this post:
Josh South (03-02-2023)
#9302
Registered Member
So if you scroll up a little bit you'll see I ordered about $2000 of parts from Z1. Well 2-3 days later Z1 started a promotion to win the new Z, modified pretty well, and $20,000 for every dollar you spend. They even have multipliers for buying specific products, like their own are worth 4x the amount of a standard spent dollar. I was a little disappointed, so I emailed them asking if I could have some entries for my order. They said no, because it was before the contest date, however since none of my stuff had shipped yet they let me cancel my order and place it again, today. The bulk of the money I spent was Z1 parts (about $1500), so that would be over 6000 entries alone! Pretty happy how this worked out, and that Z1 allowed me to do that. Some of it was just luck that they hadn't shipped yet.
The following users liked this post:
SupraOfDoom (03-02-2023)
#9303
Registered Member
The following users liked this post:
Josh South (03-02-2023)
#9304
Registered Member
#9305
Registered Member
Did the g35 HR upper manifold mod to work on my G37. Re finished a Taketa intake splash guard in H-series cerakote on my friends car.
G35 HR manifold
Cerakote
Cerakote
G35 HR manifold
Cerakote
Cerakote
The following users liked this post:
rotarymike (03-05-2023)
The following users liked this post:
Josh South (03-06-2023)
#9307
Registered Member
#9308
DIY Cheapskate/Mod
I didn't even think of the catch can scenario. That saves me a lot of money being able to run a single vs dual. After driving it a couple days I did 0-60 run and it actually helped a little bit. I consistently ran a 5.1 where before I was consistently running a 5.3. Now I just need a tune. Win Win for me. Could also be a lot of other factors for the 0-60 times but my butt dyno feels slightly more pull coming out of corners for sure.
Engine bay changed quite a bit since then, but I still use the same can and routing
Last edited by hexotic; 03-06-2023 at 08:52 PM.
The following users liked this post:
Josh South (03-07-2023)
#9310
DIY Cheapskate/Mod
Tell me about that waffle cover @hexotic .
Here's a slightly older photo with a better angle
The following users liked this post:
SupraOfDoom (03-07-2023)
#9312
DIY Cheapskate/Mod
https://parts.infinitiusa.com/a/INFI...6_US_747A.html
This is your part I believe
https://parts.infinitiusa.com/p/INFI...812-1CA0A.html
#9313
Registered Member
I like to call that the gravel holder.
The following 2 users liked this post by SupraOfDoom:
Josh South (03-08-2023),
rotarymike (03-08-2023)
#9315
Registered Member
iTrader: (1)
thanks for the info on the plastic piece guys. I'll probably look at a nearby junkyard this week just to try.
I finally put on my SPC adjustable camber arms and had it aligned. It definitely rides smoother than before but it feels weird. Should I get a little camber added in the back? Before the arms my tire wear was horrible. Perfect tread on the outside tread or so and slick towards the inside. I don't have adjustable arms in front, but they helped my toe.