C/f duckbill
The following users liked this post:
SiKHG37 (01-30-2017)
#47
Registered User
Installed mine today....Some notes:
1. Fitment is 97%, some gaps about 1.5mm in areas. The camera does not sit flush unless you modify the hole in the spoiler like the OP
2. The tape it comes provided with SUCKS. I went to Target and picked up some permanent double sided mounting tape about 1" wide. That spoiler is not going to budge
3. Overall, it looks great. I give it a 9/10
1. Fitment is 97%, some gaps about 1.5mm in areas. The camera does not sit flush unless you modify the hole in the spoiler like the OP
2. The tape it comes provided with SUCKS. I went to Target and picked up some permanent double sided mounting tape about 1" wide. That spoiler is not going to budge
3. Overall, it looks great. I give it a 9/10
#50
Enlarge all 4 sides is want I did. The camera has a rounded corners, I did enough where it just sort of fell in place. I used a fine file and test fit after every so much was taken out.
There is no mounting point. I made a bracket out of a aluminum strip and short screws
There is no mounting point. I made a bracket out of a aluminum strip and short screws
The following users liked this post:
WillCo1 (01-31-2017)
#51
Registered User
Here is a picture of the camera mounted inside the stock chrome finisher. As you can see, it's mounted in place with bracket and screws. The carbon fiber spoiler does not have a place to screw the camera in. I used Gorilla glue and Tape. I don't have a dremel so I was unable to enlarge the provided camera hole. The camera isn't flush, but it's mounted inside the spoiler at the correct alignment.
I made a DIY article:
https://www.myg37.com/forums/d-i-y-i...ml#post4106844
I made a DIY article:
https://www.myg37.com/forums/d-i-y-i...ml#post4106844
Last edited by steven92; 01-31-2017 at 08:47 AM.
The following users liked this post:
WillCo1 (01-31-2017)
#52
Installed mine today....Some notes:
1. Fitment is 97%, some gaps about 1.5mm in areas. The camera does not sit flush unless you modify the hole in the spoiler like the OP
2. The tape it comes provided with SUCKS. I went to Target and picked up some permanent double sided mounting tape about 1" wide. That spoiler is not going to budge
3. Overall, it looks great. I give it a 9/10
1. Fitment is 97%, some gaps about 1.5mm in areas. The camera does not sit flush unless you modify the hole in the spoiler like the OP
2. The tape it comes provided with SUCKS. I went to Target and picked up some permanent double sided mounting tape about 1" wide. That spoiler is not going to budge
3. Overall, it looks great. I give it a 9/10
Looks good to me!! Thanks for write up also
The following users liked this post:
steven92 (01-31-2017)
#53
Registered Member
iTrader: (2)
Did you (steven92) by chance take any photos of the underside of the CF Spoiler? Just asking because it would be nice to know if there was enough "meat" or whatever on the underside where as studs could be added so that it could also be bolted down like the OEM spoiler.
#54
Registered User
Did you (steven92) by chance take any photos of the underside of the CF Spoiler? Just asking because it would be nice to know if there was enough "meat" or whatever on the underside where as studs could be added so that it could also be bolted down like the OEM spoiler.
The following users liked this post:
The Pope (01-31-2017)
#55
#58
Premier Member
iTrader: (1)
Originally Posted by xnick101
http://www.ebay.com/itm/Carbon-Fiber-Rear-Trunk-Spoiler-Wing-Lip-Fit-for-Infiniti-G-Series-G37-2D-09-13/171884452563?_trksid=p2141725.c100338.m3726&_trkparms=aid%3D222007%26algo%3DSIC.MBE%26ao%3D1%26asc%3D20150313114020%26meid%3D273c435e017b4c2fa8e63f8158ebf62f%26pid%3D100338%26rk%3D4%26rkt%3D30%26sd%3D302166802916
are you talking about this one?
are you talking about this one?