What did you do to your coupe today?
#451
Registered Member
ANd next up is a CAI. More than likely Stillen Gen-3.
And once everything is is on I head to Chatsworth, CA to Specialty-Z for a Tune and Dyno.
#452
Yep. I still need to install my Motiv High Flow Cats. I ordered the header to cat gaskets and they should be here in a week or so. Already bought the 1/2 inch impact ratchet extensions, impact sockets and PB Blaster.
ANd next up is a CAI. More than likely Stillen Gen-3.
And once everything is is on I head to Chatsworth, CA to Specialty-Z for a Tune and Dyno.
ANd next up is a CAI. More than likely Stillen Gen-3.
And once everything is is on I head to Chatsworth, CA to Specialty-Z for a Tune and Dyno.
#453
Registered Member
#454
Registered Member
And PB Blaster is garbage. Barely better than WD-40.
I guess my list of stuff to buy just got bigger.
Thanks for the Pro-Tip blnewt.
The following users liked this post:
blnewt (12-05-2016)
#455
Registered User
Changed the end links and my clunking noise(s) are gone! New to the forum, as a contributor, but have been reading since last year, and bought an '09 37x A/T coupe last January, w/60k miles. LOVE IT! I'm a DIY kind of guy with alternate vehicles (75 IH Scout) to drive if something takes more time than immediately available, but my G is my daily driver. Why would I want to drive anything else? Thanks to everyone who contributes to these forums, as they selflessly share the joy (and maint) that driving a G is. I'm now at 80K on my G and have replaced both front sway bar end links, both front wheel bearings, all brake pads and tires. Next spring is complete brake upgrade, and with the info from this sight, I know I'm getting what I want and need. Thanks again.
The following users liked this post:
blnewt (12-05-2016)
The following users liked this post:
WillCo1 (12-05-2016)
#458
Registered Member
iTrader: (2)
Finally got around to having the OEM deck lid spoiler installed. The Opti-Coat 2.0 had cured for about 3 weeks so it should be nice and hard. Check out that water beading (the rest of the car is coated with CQuartz Finest)! The clear plastic lens on the spoiler is coated with CQuartz DLUX.
ETA: slight bit of water is leaking into the trunk during heavy rains. I'm going to pull the liner and put some sealant around the gaskets -- any recommendations as to what to use for sealant that will not degrade the rubber gaskets? I'm thinking silicone (like the kind they use in plumbing) but am open to suggestions.
ETA: slight bit of water is leaking into the trunk during heavy rains. I'm going to pull the liner and put some sealant around the gaskets -- any recommendations as to what to use for sealant that will not degrade the rubber gaskets? I'm thinking silicone (like the kind they use in plumbing) but am open to suggestions.
Last edited by Ace_07; 12-06-2016 at 05:58 PM.
#459
Registered Member
Finally got around to having the OEM deck lid spoiler installed. The Opti-Coat 2.0 had cured for about 3 weeks so it should be nice and hard. Check out that water beading (the rest of the car is coated with CQuartz Finest)! The clear plastic lens on the spoiler is coated with CQuartz DLUX.
ETA: slight bit of water is leaking into the trunk during heavy rains. I'm going to pull the liner and put some sealant around the gaskets -- any recommendations as to what to use for sealant that will not degrade the rubber gaskets? I'm thinking silicone (like the kind they use in plumbing) but am open to suggestions.
ETA: slight bit of water is leaking into the trunk during heavy rains. I'm going to pull the liner and put some sealant around the gaskets -- any recommendations as to what to use for sealant that will not degrade the rubber gaskets? I'm thinking silicone (like the kind they use in plumbing) but am open to suggestions.
The following users liked this post:
Ace_07 (12-12-2016)
#461
Premier Member
iTrader: (13)
Finally got around to having the OEM deck lid spoiler installed. The Opti-Coat 2.0 had cured for about 3 weeks so it should be nice and hard. Check out that water beading (the rest of the car is coated with CQuartz Finest)! The clear plastic lens on the spoiler is coated with CQuartz DLUX.
ETA: slight bit of water is leaking into the trunk during heavy rains. I'm going to pull the liner and put some sealant around the gaskets -- any recommendations as to what to use for sealant that will not degrade the rubber gaskets? I'm thinking silicone (like the kind they use in plumbing) but am open to suggestions.
ETA: slight bit of water is leaking into the trunk during heavy rains. I'm going to pull the liner and put some sealant around the gaskets -- any recommendations as to what to use for sealant that will not degrade the rubber gaskets? I'm thinking silicone (like the kind they use in plumbing) but am open to suggestions.