What did you do to your coupe today?
#2086
Registered Member
iTrader: (3)
Everything you need to know is in these two threads:
Heater Hose DIY#1 and,
Heater Hose DIY#2
Just search for "heater hose g37" and you'll get a ton of info and pics.
Heater Hose DIY#1 and,
Heater Hose DIY#2
Just search for "heater hose g37" and you'll get a ton of info and pics.
#2087
Registered Member
Everything you need to know is in these two threads:
Heater Hose DIY#1 and,
Heater Hose DIY#2
Just search for "heater hose g37" and you'll get a ton of info and pics.
Heater Hose DIY#1 and,
Heater Hose DIY#2
Just search for "heater hose g37" and you'll get a ton of info and pics.
The following users liked this post:
SkysG37 (10-22-2023)
#2089
#2091
Registered Member
Engine Cover
Tried to dress up the engine cover. Had a heck of a time getting paint to lay down. Painted it the first time, then spent over 2 hours removing the paint cause 90% of it bubbled...and it was clean and prepped when I started spraying
. 2nd time didn't lay very good either but for now I'm going to call it good enough.
. 2nd time didn't lay very good either but for now I'm going to call it good enough.
The following users liked this post:
mummy2 (10-28-2023)
#2092
Registered Member
Apologies for the long post.
Over the past month, installed a new exhaust system onto my RHD Japan imported Nissan Skyline 370GT Type SP.
Parts I went with:
Some photos of the installation process:
Greddy Evo GT Catback
DC Sports Polished SS Headers
AAM RHFC
Steering column bolt hits the header, steering wheel was turnable but had alot of resistance.
Heated and moulded out of the way.
Over the past month, installed a new exhaust system onto my RHD Japan imported Nissan Skyline 370GT Type SP.
Parts I went with:
- Greddy Evo GT Catback
- Only exhaust from a reputable brand compatible with a 4WAS module stuck to the back of the diff.
- AAM Resonated HFC
- They advertise that the HFC come with a J-bend O2 sensor bung to prevent CEL but mine didn't come with one? Didn't get a CEL so it doesn't really matter but it's a heads up for anyone who's looking to buy.
- DC Sports Polished SS Headers
- One of the only shorty headers that did not cost $2k+ and was quoted to fit RHD 370Z.
- It did not fit a RHD G37 so one of the pipes was modified to clear the steering column bolt.
- New O2 & Air/Fuel sensors
- Both left side sensors were seized
- Huge shoutout to Dalton and Nick from CZP for their customer service and advice.
Some photos of the installation process:
Greddy Evo GT Catback
DC Sports Polished SS Headers
AAM RHFC
Steering column bolt hits the header, steering wheel was turnable but had alot of resistance.
Heated and moulded out of the way.
The following 3 users liked this post by DB0037:
#2093
Registered Member
Stillen Generation 3
I got the Stillen Generation 3 Cold Air Intakes on.
All Done
All Done
Stillen Going On Left Side, Stock On The Right
Stock Setup
All Done
All Done
Stillen Going On Left Side, Stock On The Right
Stock Setup
The following users liked this post:
mummy2 (11-18-2023)
#2094
Administrator
iTrader: (9)
The following 2 users liked this post by Rochester:
DB0037 (11-19-2023),
liquidfluidity (01-24-2024)
#2095
Registered Member
#2096
Registered Member
iTrader: (1)
On today's 'Tales from my DA PO': They cut the firewall grommet to run power for a subwoofer. I think I've tracked down my leak to right here so my question for everyone is should I be concerned about water coming to this spot during rains and what kind of goop should I seal it with? I know I should go all the way with the sunroof drains but pulling the trim apart and inspecting them they looked fine. I didn't tear apart any further to get to the engine bay side of the drain yet.
#2097
Stayed up installing these last night. First time installing any of these parts. Just want to say thanks to those of you who have helped answer questions, concerns, and given constructive criticism. It’s much appreciated. Slowly but surely she’s coming along.
The following users liked this post:
Cortez (11-27-2023)
#2099
Registered Member
how to?
i drive a 2012 manual 6 speed coupe so im not in need of the paddle shifters, was thinking of either going oem q60 wheel or maybe an aftermarket carbon fiber wheel,
either way i still want to see if this is compatible and if so how would the heated steering wheel version work?
thanks!
#2100
Registered Member
how to?
i drive a 2012 manual 6 speed coupe so im not in need of the paddle shifters, was thinking of either going oem q60 wheel or maybe an aftermarket carbon fiber wheel,
either way i still want to see if this is compatible and if so how would the heated steering wheel version work?
thanks!
The following users liked this post:
BxG3? (01-15-2024)