Project Panda
#63
Registered Member
Enkei told me the fronts will need 18x8.5 +30 to clear front akebonos.
#65
Registered Member
There's a guy I'm following on Instagram with 18x9.5 +15 rpf1 in SBC on his g37 6 speed with akebonos and they look really aggressive.
This is how my 18x9 +35 look
Even my 18x9 +35 sticks out a bit more than I would like. The 18x9.5 +15 stick out WAY more.
#67
Registered Member
Enkei nt03+m are cheap and light.
#68
I was very disappointed over this past weekend. I was expecting the subframe collars to be at most a 1 hour job but it ended up taking me 4 hours.
First, the captive-weld nut in the chassis that the small sub-frame brace is held in by breaks on me so I had to cut the bolt off. I spent most of my time trying to find something that would fit in the space and I didn't have anything to burn it off.
I also sheared off all three bolts that held up the plastic rear shield.
During the process of installing the collars, I guess my rubber bushings were in such great condition that I had the hardest time fitting it in. I had to resort to using a jack with a tube pipe to push the collar in.
This is how it current fits in the rear. Is this normal?
I sold this particular lip a while back and bought one brand new pre-painted, but I never installed it since my bumper was in such bad shape. This lip happen to be on sale by the guy I sold it to and asked if I could buy it back. Now, I have a crappy lip with a crappy bumper. A perfect match.
First, the captive-weld nut in the chassis that the small sub-frame brace is held in by breaks on me so I had to cut the bolt off. I spent most of my time trying to find something that would fit in the space and I didn't have anything to burn it off.
I also sheared off all three bolts that held up the plastic rear shield.
During the process of installing the collars, I guess my rubber bushings were in such great condition that I had the hardest time fitting it in. I had to resort to using a jack with a tube pipe to push the collar in.
This is how it current fits in the rear. Is this normal?
I sold this particular lip a while back and bought one brand new pre-painted, but I never installed it since my bumper was in such bad shape. This lip happen to be on sale by the guy I sold it to and asked if I could buy it back. Now, I have a crappy lip with a crappy bumper. A perfect match.
#69
Super Moderator
iTrader: (3)
I was very disappointed over this past weekend. I was expecting the subframe collars to be at most a 1 hour job but it ended up taking me 4 hours.
First, the captive-weld nut in the chassis that the small sub-frame brace is held in by breaks on me so I had to cut the bolt off. I spent most of my time trying to find something that would fit in the space and I didn't have anything to burn it off.
I also sheared off all three bolts that held up the plastic rear shield.
During the process of installing the collars, I guess my rubber bushings were in such great condition that I had the hardest time fitting it in. I had to resort to using a jack with a tube pipe to push the collar in.
This is how it current fits in the rear. Is this normal?
First, the captive-weld nut in the chassis that the small sub-frame brace is held in by breaks on me so I had to cut the bolt off. I spent most of my time trying to find something that would fit in the space and I didn't have anything to burn it off.
I also sheared off all three bolts that held up the plastic rear shield.
During the process of installing the collars, I guess my rubber bushings were in such great condition that I had the hardest time fitting it in. I had to resort to using a jack with a tube pipe to push the collar in.
This is how it current fits in the rear. Is this normal?
can you post better pics of the bushing sitting? its hard to tell from the pic posted but it does look to be sitting a little high
#70
sucks to hear...almost sounds like you are working on a northern car...broken bolts seized from corrosion is usually half the working time in areas where they use road salt....tons of PB blaster and a good thread chaser set is a must up here ... I hope you post a you tube video on your install though...Iv'e had my collars sittign i nthe garage for at least a year now waiting on me getting to them...
can you post better pics of the bushing sitting? its hard to tell from the pic posted but it does look to be sitting a little high
can you post better pics of the bushing sitting? its hard to tell from the pic posted but it does look to be sitting a little high
The following users liked this post:
Baadnewsburr (04-10-2019)
#71
Registered Member
I also just installed Z1 subframe collar inserts yesterday. The top collar inserts were simple and easily fell into place. The lower collars were a bitch. I sprayed the bushing with silicone lubricant and also sprayed the collar inserts. Didn't make going in any easier. I had a rubber mallet to beat it in and didn't have any luck. Since I had the car up on a lift I decided to grab a pole jack and use a 38mm axle nut socket to help press the lower inserts in. Everything went in fine after that.
Took me about 1.5 hours and that was because I wasted a good bit of time trying to use a rubber mallet to hit the lower collar in. I finally decided to just remove part of my exhaust to get more access and use a pole jack to press it in.
Took me about 1.5 hours and that was because I wasted a good bit of time trying to use a rubber mallet to hit the lower collar in. I finally decided to just remove part of my exhaust to get more access and use a pole jack to press it in.
#72
I also just installed Z1 subframe collar inserts yesterday. The top collar inserts were simple and easily fell into place. The lower collars were a bitch. I sprayed the bushing with silicone lubricant and also sprayed the collar inserts. Didn't make going in any easier. I had a rubber mallet to beat it in and didn't have any luck. Since I had the car up on a lift I decided to grab a pole jack and use a 38mm axle nut socket to help press the lower inserts in. Everything went in fine after that.
Took me about 1.5 hours and that was because I wasted a good bit of time trying to use a rubber mallet to hit the lower collar in. I finally decided to just remove part of my exhaust to get more access and use a pole jack to press it in.
Took me about 1.5 hours and that was because I wasted a good bit of time trying to use a rubber mallet to hit the lower collar in. I finally decided to just remove part of my exhaust to get more access and use a pole jack to press it in.
I had a lot of trouble with my rear bottom collar. I had to use jack and tube to get enough force to push it in.
The following users liked this post:
Baadnewsburr (04-12-2019)
#74
Thanks for the reference pictures. Mine looks the same then and I have nothing to worry about.
Hopefully I'll have my diff bushing cut out and replaced this weekend. Once I have that done, I should be smooth sailing for the rest of the install of the differential and my exhaust.
Hopefully I'll have my diff bushing cut out and replaced this weekend. Once I have that done, I should be smooth sailing for the rest of the install of the differential and my exhaust.