HELP~All squared setups please post here!
The following users liked this post:
skrolz (03-15-2019)
#1052
Registered Member
iTrader: (5)
Anyone know how I can add more neg front camber?
had to add a 15mm spacer to clear akebonos and now the 275 40 is sticking out alot. Ive ordered a 12mm which should bring it in 3mm from here but i still need neg camber.
effective offset is now 23. With the 12mm effective offset will be 26mm.
275 40 square
had to add a 15mm spacer to clear akebonos and now the 275 40 is sticking out alot. Ive ordered a 12mm which should bring it in 3mm from here but i still need neg camber.
effective offset is now 23. With the 12mm effective offset will be 26mm.
275 40 square
#1055
Super Moderator
iTrader: (3)
Nooooo! you were living my dream of the 275 squared...lol, I get it though....
sorry I thought you were already lowered though...if you go to coils you will introduce some additional negative camber naturally at any ride height lower than you are currently, but you wont have control over it relative to the ride height without the adjustable upper control arms i ncase its not where you want it to be...if you're getting coils you may want to see if its enough to do the job before swapping the tires..
sorry I thought you were already lowered though...if you go to coils you will introduce some additional negative camber naturally at any ride height lower than you are currently, but you wont have control over it relative to the ride height without the adjustable upper control arms i ncase its not where you want it to be...if you're getting coils you may want to see if its enough to do the job before swapping the tires..
#1056
Registered Member
iTrader: (5)
Nooooo! you were living my dream of the 275 squared...lol, I get it though....
sorry I thought you were already lowered though...if you go to coils you will introduce some additional negative camber naturally at any ride height lower than you are currently, but you wont have control over it relative to the ride height without the adjustable upper control arms i ncase its not where you want it to be...if you're getting coils you may want to see if its enough to do the job before swapping the tires..
sorry I thought you were already lowered though...if you go to coils you will introduce some additional negative camber naturally at any ride height lower than you are currently, but you wont have control over it relative to the ride height without the adjustable upper control arms i ncase its not where you want it to be...if you're getting coils you may want to see if its enough to do the job before swapping the tires..
The following users liked this post:
Baadnewsburr (03-15-2019)
#1059
Registered Member
iTrader: (5)
Ok so not sure where i went wrong measuring but it definitely looks like i have room for a 10mm spacer what say you? Currently on 12mm spacer. It looks so much better with the 12 vs 15mm.
im going to hold off on the smaller tire for now as i may buy a 10mm spacer and try it. Although i tried a bolt on 10mm and less than a fingernail clearance. Perhaps not all 10mm created equal.
man these 275 are meaty im loving it.
im going to hold off on the smaller tire for now as i may buy a 10mm spacer and try it. Although i tried a bolt on 10mm and less than a fingernail clearance. Perhaps not all 10mm created equal.
man these 275 are meaty im loving it.
#1060
Registered Member
This is my current square setup on my coupe:
Akebono brakes
Eibach Pro Kit springs
19x8.5 factory sport wheels
+43 - 20mm spacers = +23 offset
225/45/19 tires
I'm very interested in the following setup:
20x9.5 Konig Oversteer
+25 (no spacers)
255/35/20
Here are the results from will they fit comparing both setups above. Can anyone advise if I'll have any issues with this? I'm thinking the offset for the new set up might be a little too low. I don't want to roll fenders or trim liner.
Appreciate any and all help and advice! Thank you!
Below is a willtheyfit comparison to Twisted's setup (orange) from above. His 275/35/20 on 20x9.5+30 setup rubs the liner a little, which I don't mind.
Akebono brakes
Eibach Pro Kit springs
19x8.5 factory sport wheels
+43 - 20mm spacers = +23 offset
225/45/19 tires
I'm very interested in the following setup:
20x9.5 Konig Oversteer
+25 (no spacers)
255/35/20
Here are the results from will they fit comparing both setups above. Can anyone advise if I'll have any issues with this? I'm thinking the offset for the new set up might be a little too low. I don't want to roll fenders or trim liner.
Appreciate any and all help and advice! Thank you!
Below is a willtheyfit comparison to Twisted's setup (orange) from above. His 275/35/20 on 20x9.5+30 setup rubs the liner a little, which I don't mind.
#1062
G37x sedan 2012 Would this fit and not rub 19x9.5 ET40 square on 255 40 19square
I have a G37x Sedan 2012.... trying to purchase some rims and tires and need assistance on the setup. Looking at 19x9.5 ET40 square, on 255x40x19 square. Would this fit okay and any rub issues? Also thinking about lowering on eibachs in the future?
Last edited by Gqaceone; 03-17-2019 at 12:23 PM. Reason: More information
#1064
G37x sedan 2012 Would this fit and not rub 19x9.5 ET40 square on 255 40 19square
I have a G37x Sedan 2012.... trying to purchase some rims and tires and need assistance on the setup. Looking at 19x9.5 ET40 square, on 255x40x19 square. Would this fit okay and any rub issues? Also thinking about lowering on eibachs in the future? Reply