MYG37.com Member Dyno Sheets
#3
Premier Member
Join Date: Jul 2007
Location: Colorado Springs, CO
Posts: 3,346
Likes: 0
Received 3 Likes
on
3 Posts
MYG37.com Member Dyno Sheets
Post questions about Dyno Sheets in another Thread or PM the dyno poster.
Here is the format for posting your dyno sheets:
1. Put the status of your car when dynoed in the Title. Example: G37 6MT with FI exhaust and BERK HFC.
2. In the main body of the text post the pic(s) of your dyno sheet. Under each post put the description of the dyno such as what run and what gear used, etc.
3. The first part of the main body of text should also specify what type of dyno was used.
=============================
To help people with which gear is 1:1 (which I didn't know at the time of my dyno) here are the Gear ratios for both AT and MT transmissions.
----------------------------------------------------------------
Trans Order Code --------------------- N/A
Trans Type ---------------------------- 5
Trans Description Cont. --------------- Automatic w/OD
Trans Description Cont. Again -------- N/A
First Gear Ratio (:1) ------------------- 3.84
Second Gear Ratio (:1) ---------------- 2.35
Third Gear Ratio (:1) ------------------ 1.52
Fourth Gear Rato (:1) ----------------- 1.00
Fifth Gear Ratio (:1) ------------------- 0.84
Sixth Gear Ratio (:1) ------------------ N/A
Reverse Ratio (:1) --------------------- 2.76
Clutch Size (in) ------------------------ N/A
Final Drive Axle Ratio (:1) ------------- 3.69
Drivetrain ------------------------------- Rear-Wheel Drive
----------------------------------------------------------------
Trans Order Code --------------------- N/A
Trans Type ---------------------------- 6
Trans Description Cont. --------------- Manual w/OD
Trans Description Cont. Again -------- N/A
First Gear Ratio (:1) ------------------ 3.79
Second Gear Ratio (:1) --------------- 2.32
Third Gear Ratio (:1) ----------------- 1.62
Fourth Gear Rato (:1) ---------------- 1.27
Fifth Gear Ratio (:1) ------------------ 1.00
Sixth Gear Ratio (:1) ----------------- 0.79
Reverse Ratio (:1) -------------------- 3.45
Clutch Size (in) ----------------------- N/A
Final Drive Axle Ratio (:1) ------------ 3.69
Drivetrain ------------------------------ Rear-Wheel Drive
Here is the format for posting your dyno sheets:
1. Put the status of your car when dynoed in the Title. Example: G37 6MT with FI exhaust and BERK HFC.
2. In the main body of the text post the pic(s) of your dyno sheet. Under each post put the description of the dyno such as what run and what gear used, etc.
3. The first part of the main body of text should also specify what type of dyno was used.
=============================
To help people with which gear is 1:1 (which I didn't know at the time of my dyno) here are the Gear ratios for both AT and MT transmissions.
----------------------------------------------------------------
Trans Order Code --------------------- N/A
Trans Type ---------------------------- 5
Trans Description Cont. --------------- Automatic w/OD
Trans Description Cont. Again -------- N/A
First Gear Ratio (:1) ------------------- 3.84
Second Gear Ratio (:1) ---------------- 2.35
Third Gear Ratio (:1) ------------------ 1.52
Fourth Gear Rato (:1) ----------------- 1.00
Fifth Gear Ratio (:1) ------------------- 0.84
Sixth Gear Ratio (:1) ------------------ N/A
Reverse Ratio (:1) --------------------- 2.76
Clutch Size (in) ------------------------ N/A
Final Drive Axle Ratio (:1) ------------- 3.69
Drivetrain ------------------------------- Rear-Wheel Drive
----------------------------------------------------------------
Trans Order Code --------------------- N/A
Trans Type ---------------------------- 6
Trans Description Cont. --------------- Manual w/OD
Trans Description Cont. Again -------- N/A
First Gear Ratio (:1) ------------------ 3.79
Second Gear Ratio (:1) --------------- 2.32
Third Gear Ratio (:1) ----------------- 1.62
Fourth Gear Rato (:1) ---------------- 1.27
Fifth Gear Ratio (:1) ------------------ 1.00
Sixth Gear Ratio (:1) ----------------- 0.79
Reverse Ratio (:1) -------------------- 3.45
Clutch Size (in) ----------------------- N/A
Final Drive Axle Ratio (:1) ------------ 3.69
Drivetrain ------------------------------ Rear-Wheel Drive
Last edited by bboysteele; 04-03-2008 at 02:14 PM.
#4
Premier Member
Join Date: Jul 2007
Location: Colorado Springs, CO
Posts: 3,346
Likes: 0
Received 3 Likes
on
3 Posts
BBoy's Stock G37 6MT
Here are the dynos I got of my stock G37 on a SuperFlow WinDyn. Did this so I know what my numbers will be before my upgrades so I know what I get after each upgrade.
Enjoy:
Stock G37 Best of the first three runs 4th gear at 4k RPM
Stock G37 three runs together in 4th gear
Stock G37 max run (4th run) at 3k RPM in 4th gear
Stock G37 Max number compared to previous three runs all in 4th gear
That is all the dynos I got.
Enjoy:
Stock G37 Best of the first three runs 4th gear at 4k RPM
Stock G37 three runs together in 4th gear
Stock G37 max run (4th run) at 3k RPM in 4th gear
Stock G37 Max number compared to previous three runs all in 4th gear
That is all the dynos I got.
Trending Topics
#8
G37 6mt Dyno Result Stock & Stillen Intake & Catback
My G37S 6MT dyno result Bone stock & Stillen Long tube intake &
Catback exhaust installed.
Catback exhaust installed.
Last edited by CrazyRuskie; 04-03-2008 at 12:42 PM.
#9
Registered User
iTrader: (1)
Join Date: Mar 2008
Location: Suburbia, CA
Posts: 171
Likes: 0
Received 0 Likes
on
0 Posts
my stock G37S baseline on a mustang
all runs were done at sea level at the stated dyno location - temp was in the 60s - don't know humidity level
First run with VSD on:
A/F for first run:
Second run with VSD off:
A/F for second run:
Third run:
First run with VSD on:
A/F for first run:
Second run with VSD off:
A/F for second run:
Third run:
#12
Registered User
iTrader: (4)
Stock vs. Magnaflow Dyno
Here's my runs performed on a Dynojet at Romar Automotive in Walden, NY. I arrived with the "installed by me" Magnaflow and that run is labeled as "Magnaflow1." We then switched back to stock, this is labeled as "Stock." The stock was then removed and replaced with the Magnaflow and it was properly tightened. Having the exhaust on the lift was way easier to properly tighten those clamps and also to make sure that the resonator hangers aren't rubbing. So, other than being quieter, it was a real treat to see it make more than the 3.2hp and 1.1tq put down by my leaky install! I was told that it's a common mistake to not tighten the clamps enough and that they need to be completed closed on the spacer inside the clamp.
So, the Magnaflow when properly installed got me 269hp/228/tq vs 260hp/219tq for the stock. Not bad for less than $500!
Note 1: The spike on run 3 and the weird dropoff after 6200 rpms is due to the auto which does not take kindly to dyno testing! Even in DS mods and paddle shifting with the VCM off, it would still throw an upshift to 5th right at 6500rpms no matter what. Therefore, ignore the graph after 6000 rpms and no, I didn't get 274.65tq. The real figures for torque I had printed out due this anomoly are 219 stock, 223 leaky Magnaflow, 228 proper Magnaflow.
Note 2: Run conditions were between 74 and 75 degrees with a humidity of 29%. All runs done in 4th gear.
So, the Magnaflow when properly installed got me 269hp/228/tq vs 260hp/219tq for the stock. Not bad for less than $500!
Note 1: The spike on run 3 and the weird dropoff after 6200 rpms is due to the auto which does not take kindly to dyno testing! Even in DS mods and paddle shifting with the VCM off, it would still throw an upshift to 5th right at 6500rpms no matter what. Therefore, ignore the graph after 6000 rpms and no, I didn't get 274.65tq. The real figures for torque I had printed out due this anomoly are 219 stock, 223 leaky Magnaflow, 228 proper Magnaflow.
Note 2: Run conditions were between 74 and 75 degrees with a humidity of 29%. All runs done in 4th gear.
Last edited by ironchef2008; 08-16-2008 at 02:30 PM.
#13
Premier Member
Join Date: Jul 2007
Location: Colorado Springs, CO
Posts: 3,346
Likes: 0
Received 3 Likes
on
3 Posts
Stock dyno against Berk HFC, Fast Intentions Carbon Fiber Exhaust, and Stillen CAI 3
Isn't this beautiful?
34HP and 17TQ increase over stock. And they said bolt-ons didn't produce any power. BTW these runs were all done on the same dyno in 4th gear. And the stock dyno was done in a temp of 64 degrees F and the modded dyno was done in a temp of 91 F.
34HP and 17TQ increase over stock. And they said bolt-ons didn't produce any power. BTW these runs were all done on the same dyno in 4th gear. And the stock dyno was done in a temp of 64 degrees F and the modded dyno was done in a temp of 91 F.
#15
I used to have a 350z hence my reason for being here, I now own a Mazdaspeed 3, below is my dyno.
Car Mods:
CP-E FMIC
CP-E CAI
CP-E Catted DP
Denso ITV222 Plugs
HKS SSQV2 BOV
Cobb AccessPort v1.03L Stage 2 91oct+FMIC
My best run was 339hp/330lb-ft at crank and 280.5whp
Run 1
Run 2
Run 3
All 3 runs combined
Car Mods:
CP-E FMIC
CP-E CAI
CP-E Catted DP
Denso ITV222 Plugs
HKS SSQV2 BOV
Cobb AccessPort v1.03L Stage 2 91oct+FMIC
My best run was 339hp/330lb-ft at crank and 280.5whp
Run 1
Run 2
Run 3
All 3 runs combined